tlp113 2007-10-01 1 toshiba photocoupler gaa ? as ired & photo ? ic tlp113 isolated line receiver simplex / multiplex data transmission computer ? peripheral interface microprocessor system interface digital isolation for a / d, d / a conversion the toshiba mini flat coupler tlp113 is a small outline coupler, suitable for surface mount assembly. tlp113 consists of a gaa ? as light emitting diode, optically coupled to an integrated high gain, high speed phot odetector whose output is an open collector, schottky clamped transistor. z input current thresholds: i f =10ma(max.) z switching speed: 10mbd(typ.) z ttl / lsttl compatible: v cc =5v z guaranteed performance over temp.: 0~70c z isolation voltage: 2500vrms(min.) z ul recognized: ul1577 file no. e67349 schematic v cc gnd v o i cc i o 6 5 4 1 3 i f v f (note) a 0.1 f bypass capacitor must be connected between pins 4 and 6. pin configuration (top view) 1 : anode 3 : cathode 4 : gnd 5 : output (open collector) 6 : v cc gnd 1 3 4 5 6 v cc unit in mm toshiba 11 ? 4c2 weight: 0.09 g (typ.) input output hh h l l truth table (positive logic)
tlp113 2007-10-01 2 absolute maximum ratings (ta = 25c) characteristic symbol rating unit forward current i f 20 ma pulse forward current (note 1) i fp 40 ma peak transient forward current (note 2) i fpt 1 a led reverse voltage v r 5 v output current i o 25 ma output voltage v o 7 v supply voltage (1 minute maximum) v cc 7 v detector output power dissipation p o 40 mw operating temperature range t opr ?40~85 c storage temperature range t stg ?55~125 c lead solder temperature (10s) t sol 260 c isolation voltage (ac, 1 min., rh 60%, note 4) bv s 2500 vrms note: using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operat ing temperature/current/voltage, etc. ) are within the absolute maximum ratings and the operating ranges. please design the appropriate reliability upon reviewing the toshiba semiconductor reliability handbook (?handling precautions?/?derating concept and methods?) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). (note 1) 50% duty cycle, 1ms pulse width. (note 2) pulse width 1 s, 300pps. recommended operating conditions characteristic symbol min. typ. max. unit input voltage, low level v fl ? 3 0 1.0 v input current, high level i fh 13* 16 20 ma supply voltage** v cc 4.5 5 5.5 v fan out (ttl load, each channel) n D D 8 D operating temperature t opr 0 D 70 c note: recommended operating conditions are given as a design guideline to obtain expected performance of the device. additionally, each item is an independent guide line respectively. in developing designs using this product, please confirm specified characteristics shown in this document. * 13ma is a guard banded value which al lows for at least 20% ctr degradation. initial input current threshold value is 10ma or less. **this item denotes operating ranges, not m eaning of recommended operating conditions.
tlp113 2007-10-01 3 electrical characteristics (unless otherwise specified, ta=0~70c, v cc =4.5~5.5v, v fl 1.0v) characteristic symbol test condition min. typ. max. unit forward voltage v f i f =10ma, ta=25c D 1.65 1.80 v forward voltage temperature coefficient v f / ta i f =10ma D ? 2 D mv / c reverse current i r v r =5v, ta=25c D D 10 a capacitance between terminals c t v f =0, f=1mhz, ta=25c D 45 D pf v f =1.0, v o =5.5v D D 250 high level output current i oh v f =1.0, v o =5.5v, ta=25c D 0.5 10 a low level output voltage v ol i f =10ma i ol =13ma(sinking) D 0.4 0.6 v "h level output l level output" input current i fh i ol =13ma(sinking) v ol =0.6v D D 10 ma high level supply current i cch v cc =5.5v, i f =0 D 7 15 ma low level supply current i ccl v cc =5.5v, i f =16ma D 12 18 ma input ?output insulation leakage current i s v s =3540v, t=5s ta=25c (note 4) D D 100 a isolation resistance r s r.h. 60%, v s =500v dc ta=25` (note 4) 510 10 10 14 D stray capacitance between input to output c s v s =0, f=1mhz ta=25` (note 4) D 0.8 D pf * all typical values are v cc =5v, ta=25c
tlp113 2007-10-01 4 switching characteristics (v cc =5v, ta=25c) characteristic symbol test cir ? cuit test condition min. typ. max. unit propagation delay time (h l) t p hl 1 i f =0 16ma c l =15pf, r l =350 D 60 120 ns propagation delay time (l h) t p lh 1 i f =16 0ma c l =15pf, r l =350 D 60 120 ns output rise ?fall time (10 ? 90%) t r , t f 2 r l =350 , c l =15pf i f =0 16ma D 30 D ns common mode transient imunity at high output level cm h 2 i f =0ma, v cm =200v p? p v o(min) =2v, r l =350 D 200 D v / s common mode transient imunity at low output level cm l 2 i f =16ma, v cm =200v p? p v o(max) =0.8v, r l =350 D ?500 D v / s (note 4) device considered a two ? terminal device: pins 1 and 3 shorted together, and pins 4, 5 and 6 shorted together. (note 5) the v cc supply voltage to each tlp113 is olator must be bypassed by 0.1 f capacitor, this can be either a ceramic or solid tantalum capacitor with good high frequency characteristic and should be connected as close as possible to package v cc and gnd pins of each device. (note 6) maximum electrostatic discharge voltage for any pins: 180v(c=200pf, r=0)
tlp113 2007-10-01 5 test circuit 1: switching time test circuit c l is approximately 15pf which includes probe and stray wiring capacitance. test circuit 2: common mode transient immunity test circuit s) ( f t 160(v) = l c s) ( r t 160(v) = c , c l is approximately 15pf which includes probe and stray wiring capacitance. 16ma 8ma 0ma 5v 4.5v 1.5v 0.5v v ol t plh t phl t f t r v o i f v o output monito r v cc = 5v v cc gnd c l pulse input pw = 100 s duty ratio = 1 / 10 i f monitor 350? 0.1 f 200v 90% 0v 5v 2v 0.8v v ol t r t f v o v cm v o output monito r v cc = 5v v cc gnd c l pulse gen z o = 50? v cm i f 10% v o (i f = 10ma) (i f = 0ma) 350? 0.1 f
tlp113 2007-10-01 6 v f / ta ? i f forward current i f (ma) forward voltage temperature coefficient v f / ta ( m v / c ) ? 4.0 0.1 ? 2.4 ? 3.2 ? 1.6 0.3 1 5 10 ? 0.8 30 3 0.5 0 ? 25c 25? 70c i oh ? ta ambient temperature ta (c) high level output current i oh ( a) 10 3 0.5 0.3 80 60 40 20 0 ? 20 0.1 1 5 v f = 1.0v v cc = 5.5v v o = 5.5v 0.05 v o l ? ta ambient temperature ta (c) 0 20 40 60 80 0.30 0.35 0.40 0.50 12.8ma 9.6ma 6.4ma low level output voltage v ol (v) i ol = 16ma i f = 10ma v cc = 5.5v ? 20 0.45 i f ? v f forward voltage v f (v) forward current i f (ma) 100 1 10 1.2 1.4 1.6 1.8 1 0.1 0.01 2.0 ta = 70c 25c 0c v o ? i f forward current i f (ma) output voltage v o (v) 8 2 6 4 0 2 6 8 0 10 4 r l = 350 ? 1k ? 4k ? 10 v cc = 5v ta = 25 c forward current i f (ma) 6 10 4 8 2 0 8 6 4 2 0 output voltage v o (v) v o ? i f ta = 0 c 10 v cc = 5v r l = 350 ? r l = 4k ? ta = 70c
tlp113 2007-10-01 7 forward current i f (ma) t phl , t plh ? i f propagation delay time t phl, t plh (ns) 120 100 18 20 20 16 14 12 10 40 80 60 1k ? 4k ? r l = 4k ? ta = 25 c v cc = 5v t phl t plh 350 ? 1k ? r l = 350 ? t r, t f ? t a ambient temperature ta (c) rise, fall time t r , t f (ns) 300 220 80 0 0 120 260 40 1k ? 4k ? r l = 350 ? r l = 4k ? 20 40 60 80 ? 20 if=16ma v cc = 5v t f t r 350 ? 1k ? ambient temperature ta (c) 120 80 60 40 20 ? 20 0 40 20 0 60 propagation delay time t phl, t plh (ns) 80 100 i f = 16ma v cc = 5v t phl t plh t phl , t plh ? ta r l = 4k ? 4k ? 1k ? r l = 350 ? 350 ? 1k ?
tlp113 2007-10-01 8 restrictions on product use ? toshiba corporation, and its subsidiaries and affiliates (collect ively ?toshiba?), reserve the right to make changes to the in formation in this document, and related hardware, software a nd systems (collectively ?product?) without notice. ? this document and any information herein may not be reproduced without prior written permission from toshiba. even with toshiba?s written permission, reproduction is permissible only if reproducti on is without alteration/omission. ? though toshiba works continually to improve product?s quality and reliability, product can malfunction or fail. customers are responsible for complying with safety standards and for providi ng adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunc tion or failure of product could cause loss of human life, b odily injury or damage to property, including data loss or corruption. before creating and producing designs and using, customers mus t also refer to and comply with (a) the latest versions of all re levant toshiba information, including without limitation, this d ocument, the specifications, the data sheets and application notes for produc t and the precautions and conditions set forth in the ?tosh iba semiconductor reliability handbook? and (b) the instructions for the application that product will be used with or for. custome rs are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining th e appropriateness of the use of this product in such design or applications; (b) evaluat ing and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operat ing parameters for such designs and applications. toshiba assumes no liability for customers? product design or applications. ? product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measur ing equipment, industrial robots and home elec tronics appliances) or for specif ic applications as expressly stated in this document . product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality a nd/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or se rious public impact (?unintended use?). unintended use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic s ignaling equipment, equipment used to control combusti ons or explosions, safety devices, elevators and escala tors, devices related to el ectric power, and equipment used in finance-relat ed fields. do not use product for unintended use unless specifically permitted in thi s document. ? do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy product, whether in whole or in part. ? product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. ? the information contained herein is presented only as guidance for product use. no re sponsibility is assumed by toshiba for an y infringement of patents or any other intellectual property rights of third parties that may result from the use of product. no license to any intellectual property right is granted by this documen t, whether express or implied, by estoppel or otherwise. ? absent a written signed agreement, except as provid ed in the relevant terms and conditions of sale for product, and to the maximum extent allowable by law, toshiba (1) assumes no liability whatsoever, including without limitation, indirect, co nsequential, special, or incidental damages or loss, including without limitation, loss of profit s, loss of opportunities, business interruption and loss of data, and (2) disclaims any and all express or implied warranties and conditions related to sale, use of product, or information, including warranties or conditions of merchantability, fitness for a particular purpose, accuracy of information, or noninfringement. ? gaas (gallium arsenide) is used in product. ga as is harmful to humans if consumed or absorbed, whether in the form of dust or vapor. handle with care and do not break, cut, crush, grind, dissolve chemically or otherw ise expose gaas in product. ? do not use or otherwise make available product or related soft ware or technology for any milit ary purposes, including without limitation, for the design, development, use, stockpiling or manufa cturing of nuclear, chemical, or biological weapons or missi le technology products (mass destruction weapons). product and related software and technology may be controlled under the japanese foreign exchange and foreign trade law and the u.s. export administration regulations. export and re-export of product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. ? please contact your toshiba sales representative for details as to environmental matters such as the rohs compatibility of pro duct. please use product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled subs tances, including without limitation, the eu rohs directive. toshiba assu mes no liability for damages or losses occurring as a result o f noncompliance with applicable laws and regulations.
|
